- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Let's discuss solid sheeting the inside of a house
Posted on 2/1/19 at 1:20 pm
Posted on 2/1/19 at 1:20 pm
talking about 1/2" plywood or OSB on all walls prior to installation of sheetrock.
What's the pros and cons other than $?
What's the pros and cons other than $?
Posted on 2/1/19 at 1:23 pm to poochie
Con: $
Pro: you don’t have to find a stud to hang a picture.
Pro: you don’t have to find a stud to hang a picture.
Posted on 2/1/19 at 1:25 pm to poochie
does make for a very solid and less noisy home, no concerns of trying to find a stud to hang dat heavy arse crap in dat special place the lil miss wants it, consider doing the ceilings as well...
Posted on 2/1/19 at 1:55 pm to poochie
weight could be an issue depending on some things that could come into play. Like an older home that is pier and beam.
Posted on 2/1/19 at 2:00 pm to poochie
Will never be able to hide joints other than adding a trim board over the seam. Overall with corners and joints it will never be as "finished" as a sheetrock house. Painting is difficult because knot hole are always going to try and bleed through. I would have a hard time living a house house without light colors.
But if you like rustic looking then it might be your ticket.
But if you like rustic looking then it might be your ticket.
Posted on 2/1/19 at 2:02 pm to Chuker
quote:
Will never be able to hide joints other than adding a trim board over the seam. Overall with corners and joints it will never be as "finished" as a sheetrock house. Painting is difficult because knot hole are always going to try and bleed through. I would have a hard time living a house house without light colors.
But if you like rustic looking then it might be your ticket.
read it again. plywood installed prior to sheetrock.
Posted on 2/1/19 at 2:02 pm to poochie
Just seems incredibly unnecessary.
Hanging typical pictures, etc. from sheetrock anchors is not typically a problem. You can sheet behind the typical places that need it (curtains, TVs, etc.) without doing the entire house.
It would definitely add to the structural stability of the home. Also serve as fairly solid sound proofing.
Insulation may be affected. Some insulation vapor barriers shouldn't be in direct contact with flammable surfaces, but I imagine this can be planned around.
All your door jambs would have to be adjusted and non-standard sizes (assuming you sheeted over a standard 2x4 with 1/2" sheetrock).
Any work done after construction would be a little more difficult. Fishing wires, adding receptacles/cable connections, etc. are a more difficult than without the sheeting.
Hanging typical pictures, etc. from sheetrock anchors is not typically a problem. You can sheet behind the typical places that need it (curtains, TVs, etc.) without doing the entire house.
It would definitely add to the structural stability of the home. Also serve as fairly solid sound proofing.
Insulation may be affected. Some insulation vapor barriers shouldn't be in direct contact with flammable surfaces, but I imagine this can be planned around.
All your door jambs would have to be adjusted and non-standard sizes (assuming you sheeted over a standard 2x4 with 1/2" sheetrock).
Any work done after construction would be a little more difficult. Fishing wires, adding receptacles/cable connections, etc. are a more difficult than without the sheeting.
Posted on 2/1/19 at 2:09 pm to poochie
I have 3/4" pine tongue and groove walls throughout my house. It looks good, holds up well, and I don't have to find studs. Running wires is a huge PITA though, because there is a 2x4 horizontally behind the chair rail everywhere
Posted on 2/1/19 at 2:24 pm to poochie
Strong arse house. Quieter as well.
Posted on 2/1/19 at 2:39 pm to jimbeam
Stronger when factoring what? What’s it going to do that a non-SS house would?
Posted on 2/1/19 at 3:05 pm to poochie
quote:
Stronger when factoring what? What’s it going to do that a non-SS house would?
Wind resistance (hurricane/tornadoes) and settling.
Walls should also be much squarer, and house should be more air tight.
Posted on 2/1/19 at 3:21 pm to poochie
Increases the shear or racking loads by transmitting the loads to the sheathing through the fastener system. If there is an earthquake you're good. Tornado better than your neighbors without plywood
Posted on 2/1/19 at 3:23 pm to poochie
If I ever build it will be solid sheeted. My dad did this when he built and like others have said it is a quiet house and you can hang what you want where you want it. Maybe adds $5k to the project
Posted on 2/1/19 at 3:24 pm to LSUtigerME
Right but at what point does that matter? Are we seeing non-ss houses falling over next to ss ones? I’m honesty leaning towards it but I think the only tangible benefits are anecdotaly quieter and easier to hang things on walls.
How would it make the walls “squarer”?
How would it make the walls “squarer”?
Posted on 2/1/19 at 3:24 pm to bayoudude
$8k on 2600sf, walls only.
Posted on 2/1/19 at 3:25 pm to poochie
I didnt solid sheet my entire house, just my closets. I went with 3/4" in there due to the amount of weight from hanging clothes and stuff. I also ran some 2x8s horizontally and have an electrical outlet on the walls where I knew I would have TVS in mine and my kids rooms.
I would say do that at minimum.
I would say do that at minimum.
Posted on 2/1/19 at 10:07 pm to poochie
I know they use to build homes like that in coastal areas where they expect a lot of wind.
Some people claim it makes for a stronger house.
Some people claim it makes for a stronger house.
Posted on 2/1/19 at 10:20 pm to poochie
At a certain point sheeting all the walls is overkill. Most of the time the exterior corners are sheeted and that stiffens up the entire wall just fine.
Posted on 2/2/19 at 1:59 am to bayoudude
Use Screws instead of nails.
Posted on 2/2/19 at 2:10 am to poochie
quote:
How would it make the walls “squarer”?
I don't see how it could, unless they are talking about vertically square, as in leaning as the house ages, but that's what slap studs are for?
If that shite is framed out of square, plywood aint gonna do no magic on Mexican Framers.
This post was edited on 2/2/19 at 4:15 am
Popular
Back to top
Follow TigerDroppings for LSU Football News