- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Coaching Changes
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
DIY LVP install…tell me what I need to know.
Posted on 11/21/25 at 1:01 pm
Posted on 11/21/25 at 1:01 pm
Thanks fellas!
12
Posted on 11/21/25 at 1:42 pm to TexasHand
Be sure to leave a perimeter back.
Prepare for sore back.
Prepare for sore back.
Posted on 11/21/25 at 2:04 pm to TexasHand
hire someone to do it
Posted on 11/21/25 at 2:26 pm to TexasHand
quote:
tell me what I need to know.
Read the installation instructions for that flooring. Follow those instructions or you will void any kind of warranty that is available.
Posted on 11/21/25 at 2:49 pm to TexasHand
Get a lvp install kit from Lowe's or Home Depot. Make sure you use the spacers around the perimeter
Posted on 11/21/25 at 3:06 pm to TexasHand
How much of it are you putting down? If you already own a miter saw or table saw, get the dedicated PCD Pergo blades for cutting the stuff. If you don't then get a LVP cutter, these are great for smaller installs and you can cut right there in the room.
LVP cutter
Those flooring kits are ok but get a decent non-marring flooring mallet and a set of flooring clamps, sometimes you can get a few layers in and notice a joint between planks opened a little, the ratchet clamp will allow you to squeeze that back tight.
LVP cutter
Those flooring kits are ok but get a decent non-marring flooring mallet and a set of flooring clamps, sometimes you can get a few layers in and notice a joint between planks opened a little, the ratchet clamp will allow you to squeeze that back tight.
This post was edited on 11/21/25 at 3:07 pm
Posted on 11/21/25 at 5:54 pm to TexasHand
Total of 1100 sqft over concrete slab. I’ve laid tile a few times so I’m accustomed to a sore back lol. I refuse to pay someone 3k to do something I can knock out. Me and YouTube go wayyy back. Figured I’d ask you fellas that may have experience with it.
Posted on 11/21/25 at 5:58 pm to TexasHand
Buy a ton of spacers. Invest in a laminate cutter. Get the highest quality LVP you can afford -- it will make installing it much, much easier.
Posted on 11/21/25 at 6:29 pm to TexasHand
go around with a straight edge and see how uneven your concrete is. If its bad then it can lead to hollow spot under some areas. Aside from a hollow sounding floor, it may start to separate joints from being flexed everytime its stepped on. If carpet was there from the builder, it could take a bunch of expensive leveling concrete to bring it up to snuff. One thing for sure, the instructions will ask for an almost unheard of level of flatness. Something like 1/16" in 6ft. I think they say that because they know no floor is going to meet those specs and it gives them an out for warranty claims.
I've always just scored and snapped crosscuts with utility knife. Or if its the real thick stuff used a jigsaw over a trash can station to collect the sawdust. Table saw outside for the rips.
I've always just scored and snapped crosscuts with utility knife. Or if its the real thick stuff used a jigsaw over a trash can station to collect the sawdust. Table saw outside for the rips.
Posted on 11/21/25 at 6:31 pm to TexasHand
Just completed 1st of 3 rooms. Make sure concrete subfloor is clean and level. Take your time. As you lay each row make certain row it straight and locked in. Watch end connection and make sure there is no debris or dirt getting between ends.
Posted on 11/21/25 at 6:32 pm to TheOcean
quote:
Buy a ton of spacers
I have always used the scraps from cutting the LVP flooring as spacers
Posted on 11/21/25 at 6:46 pm to TexasHand
I vest in a good pair of knee pads.
Not very difficult. Takes a little time, so don't get in a hurry
Use a 6 mil underlayment if putting on concrete floor
Use a miter saw to cut pieces.
Not very difficult. Takes a little time, so don't get in a hurry
Use a 6 mil underlayment if putting on concrete floor
Use a miter saw to cut pieces.
Posted on 11/22/25 at 11:33 am to TexasHand
This guy is the GOAT for LVP install
https://www.sothatshowyoudothat.com/
I would also spend time on his youtube channel until you feel comfortable with everything. There are a lot of questions to answer if you've never done it before.
YouTube - So That's How You Do That!
https://www.sothatshowyoudothat.com/
I would also spend time on his youtube channel until you feel comfortable with everything. There are a lot of questions to answer if you've never done it before.
YouTube - So That's How You Do That!
Posted on 11/22/25 at 9:33 pm to 9rocket
quote:
Prepare for sore back.
And knees. I've done a couple of installs, and every time my knees kill me for days afterwards. I use kneepads, but they still hurt. I'd hate to feel them without the pads.
Posted on 11/23/25 at 8:08 am to weadjust
quote:
I have always used the scraps from cutting the LVP flooring as spacers
We do, too. But your first attempt it is usually easier to buy the spacers
Posted on 11/24/25 at 2:00 pm to TexasHand
I installed 25 boxes of Pergo from Home Depot. I bought the install kit tools and went at it. Other than sore legs, some careful cuts near door frames, and the loud clacking of connecting the planks, all went well for my bedroom, including the walk in closets. 
Page 1 of 1
Popular
Back to top
Follow TigerDroppings for LSU Football News