- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Posted on 11/23/20 at 7:22 pm to CharlesLSU
quote:
but it’s kind of a novelty
What?
Posted on 11/23/20 at 7:28 pm to Carson123987
quote:
someone bought my honey badger pistol for $4500
I have a CZ Scorpion micro with a Franklin Armory binary trigger. The triggers are selling for over $900 on GB. Saw a gun just like mine sold for $2750. Might just sell mine if I could get $2700.
Posted on 11/30/20 at 9:39 pm to Carson123987
May have been posted but on the s&w MP15 front sight... Will it impair optics whatsoever?
I have read the gas block with the roll pins is rock solid and better to cut the sight off than add AM screw set gas blocks. Opinions?
I have read the gas block with the roll pins is rock solid and better to cut the sight off than add AM screw set gas blocks. Opinions?
Posted on 11/30/20 at 9:54 pm to Sparetime
Most optics are raised to a height so you can use the iron sights as backups. It’s called co-witness.
On some you’ll have the front post in the center of your optic and there are some that it is on the lower 3rd of the optic.
On some you’ll have the front post in the center of your optic and there are some that it is on the lower 3rd of the optic.
Posted on 11/30/20 at 9:55 pm to udtiger
quote:
What about AR-10s?
What about them? They’re great.
Posted on 11/30/20 at 9:56 pm to bbvdd
quote:
quote:
What about AR-10s?
What about them? They’re great.
I just didn't know whether they could be discussed in this thread.
Posted on 11/30/20 at 9:57 pm to udtiger
Sure. I have two.
.308 and a 6.5cm.
.308 and a 6.5cm.
Posted on 11/30/20 at 11:39 pm to Sparetime
quote:
I have read the gas block with the roll pins is rock solid and better to cut the sight off than add AM screw set gas blocks. Opinions?
It’s solid to the point where it’s a pain in the arse to remove it. It’s not optimal for optics but it’s not a big deal either. If I was going to cut it off I’d probably want it covered with a longer rail.
Posted on 12/1/20 at 9:00 am to Sparetime
quote:
I have read the gas block with the roll pins is rock solid and better to cut the sight off than add AM screw set gas blocks. Opinions?
Drive them out from left to right
Posted on 12/1/20 at 9:11 pm to Flats
Getting the gas block is not a problem. What blocks would you recommend with a longer rail?
Posted on 12/1/20 at 9:36 pm to Sparetime
I have a few superlative arms low profile adjustable blocks. They’re pretty great.
Posted on 12/1/20 at 11:30 pm to Sparetime
Any low profile block, although the cuts through the barrel for the drift pins in your existing sight base might mean you’ll need a clamp-on instead of the more typical set screw type. I have a Aero Precision adjustable that I like, but gas blocks are pretty simple. Pick a reputable manufacturer of your choice, but if you’re going to cover it with a rail anyway I’d just leave the cut-down front sight base.
Posted on 12/15/20 at 2:59 pm to Flats
Thoughts on a 11.5" 7.62x39 pistol build?
Posted on 12/24/20 at 10:04 am to harvey
quote:
Wound like advice of gun owners on this.
Its fine. Do it
Posted on 12/25/20 at 4:26 pm to harvey
I bought that one in May and love it.
I would love to get a 3x or 6x magnification for it that flips out of the way.
I also would like to change out the hand guard.
Does anyone have any recommendations?
I would love to get a 3x or 6x magnification for it that flips out of the way.
I also would like to change out the hand guard.
Does anyone have any recommendations?
Posted on 12/25/20 at 7:02 pm to LSUSUPERSTAR
Midwest industries 14 or 15 inch slim handguard in m-lok. You're probably gonna need a low profile gas block too.
Posted on 12/26/20 at 8:21 am to upgrayedd
quote:
Midwest industries 14 or 15 inch slim handguar
Seconded. I put one on my last build and absolutely love it. Very lightweight and feels perfect to handle. Also well priced. In the pic below the one on the far right has that handguard.
Popular
Back to top
Follow TigerDroppings for LSU Football News