
- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Coaching Changes
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Switching to adjustable gas block
Posted on 11/18/26 at 2:23 pm
Posted on 11/18/26 at 2:23 pm
I'm gonna change out the gas block on my 300 BO to an adjustable one. I know there are tons of videos to walk me through it, but waned to check in with the OB
is this much of a chore? We talking a one beer job or two?
what adjustable gas block do you prefer?
Does the brand really even matter here?
any other thoughts or pointers?
is this much of a chore? We talking a one beer job or two?
what adjustable gas block do you prefer?
Does the brand really even matter here?
any other thoughts or pointers?
Posted on 11/18/26 at 2:42 pm to LoneStarTiger
Superlative Arms is one of the best.
Just measure and make sure you order the right size and also whether you need a clamp on or have a dimpled barrel.
It’s easy. Remove the hand guard, loosen the Allen screws on the current block and with a punch push out the roll pin holding the gas tube.
Reverse that to install the adjustable.
10 min at the most.
If you have an a-frame sight, throw that all out.
There is a pin on the bottom that is a directional pin. I understand it’s a bit of a pain to remove them but have never tried.
Just measure and make sure you order the right size and also whether you need a clamp on or have a dimpled barrel.
It’s easy. Remove the hand guard, loosen the Allen screws on the current block and with a punch push out the roll pin holding the gas tube.
Reverse that to install the adjustable.
10 min at the most.
If you have an a-frame sight, throw that all out.
There is a pin on the bottom that is a directional pin. I understand it’s a bit of a pain to remove them but have never tried.
Posted on 11/18/26 at 3:54 pm to LoneStarTiger
Depends on your handguard. I have a BCM handguard that's heat fit and it was a pain in the arse. If it's a regular fit then it shouldn't be too bad.
+1 for Superlative Arms
+1 for Superlative Arms
Posted on 11/18/26 at 4:05 pm to LoneStarTiger
Super easy. I have the SA as well. My only issue had nothing to do with the gas block, but the barrel. The gas port was not big enough to make use of the entire adjustable range. I had to drill out the port in the barrel slightly to cycle subsonic rounds reliably. Even with that, it was a simple task just split between a range session.
Posted on 11/18/26 at 4:34 pm to LoneStarTiger
I’ve had an adjustable block in a box in a drawer for my mini 30 for years, never got up the nerve to swap it out. The mini flings brass 30’ away, but you have to be careful dialing it back or it won’t cycle low power rounds.
Maybe one day ill get it on the bench. It’s a little intimidating
Maybe one day ill get it on the bench. It’s a little intimidating
Posted on 11/18/26 at 4:54 pm to cgrand
RE: Mini14/30 - 9/64 Allen wrench, screws will be tight. Tighten screws equally on reinstall so the gaps in the upper and lower portion of the gas block are equal.
This post was edited on 11/18/26 at 4:56 pm
Posted on 11/18/26 at 8:17 pm to LoneStarTiger
It's a fairly easy swap. It's slightly tougher if your current one is staked, but nothing a little elbow grease can't handle. The most tedious part will be the roll pin connecting the tube to the block. It helps if you have a punch set.
I'd recommend applying loctite to the gas block and handguard screws when you put it back together.
I'd recommend applying loctite to the gas block and handguard screws when you put it back together.
Posted on 11/18/26 at 8:33 pm to LoneStarTiger
It really depends on what is currently on your rifle and what you are installing.
If they are both bolt ons, it's an easy job.
If you have a pinned block on it now, as some have mentioned, it can get pretty damn challenging. It takes more than "some elbow grease" in some cases. The pins are directional and no amount of beating on them in the wrong direction will get them out. You also really need a proper disassembly block that supports the barrel. Just chucking it up in a vise and going at it with a punch and hammer isn't great for your barrel.
For the bolt on models, fine for a play rifle or a match gun but not ideal for a "duty" rifle. They can and will loosen over time, shift around the barrel cutting off the gas port and the adjustment screws can move.
I have adjustables on most of my play guns and a fixed block on my go-to-war rifle. YMMV.
If they are both bolt ons, it's an easy job.
If you have a pinned block on it now, as some have mentioned, it can get pretty damn challenging. It takes more than "some elbow grease" in some cases. The pins are directional and no amount of beating on them in the wrong direction will get them out. You also really need a proper disassembly block that supports the barrel. Just chucking it up in a vise and going at it with a punch and hammer isn't great for your barrel.
For the bolt on models, fine for a play rifle or a match gun but not ideal for a "duty" rifle. They can and will loosen over time, shift around the barrel cutting off the gas port and the adjustment screws can move.
I have adjustables on most of my play guns and a fixed block on my go-to-war rifle. YMMV.
Posted on 11/19/26 at 7:59 am to LoneStarTiger
quote:
is this much of a chore? We talking a one beer job or two?
One beer to take everything out including finding all your tools.
One beer to install it.
One beer to tune it. You have to load one road at a time in a mag and cycle it the normal way and shoot it and have the bolt lock open on the empty mag. Start with it mostly closed and keep firing one at a time while adjusting the block to allow more gas flow between each shot. When you get it to where it locks open on the empty mag, loosen the air flow screw another 2 turns and then lock in the lock screw.
Posted on 11/19/26 at 8:52 am to Squirrelmeister
quote:
One beer to take everything out including finding all your tools.
One beer to install it.
One beer to tune it. You have to load one road at a time in a mag and cycle it the normal way and shoot it and have the bolt lock open on the empty mag. Start with it mostly closed and keep firing one at a time while adjusting the block to allow more gas flow between each shot. When you get it to where it locks open on the empty mag, loosen the air flow screw another 2 turns and then lock in the lock screw.
perfect response. I ordered an SA block last night after getting home and seeing which kind I need.
Posted on 11/19/26 at 9:51 am to LoneStarTiger
quote:
perfect response. I ordered an SA block last night after getting home and seeing which kind I need.
Nice. Being over-gassed beats up your bolt unnecessarily and adds more recoil and lowers your bullet muzzle velocity. When adding a suppressor, that often adds back pressure and can result in over-gassing so an adjustable block can and should be used to lower the gas coming back to work the bolt. It’ll also make it a little quieter too as a larger portion of the gas will be traveling through and out the suppressor.
Posted on 11/19/26 at 10:12 am to bbvdd
quote:do all this...I did mine in 10 minutes. I would also get a new gas tube to make it easier b/c mine was stuck in the old gas block. I buy 500 packs of subs from reputable and not-so-reputable online sources and makes it very easy to adjust for each new batch of ammo.
measure and make sure you order the right size and also whether you need a clamp on or have a dimpled barrel.
Posted on 11/19/26 at 10:15 am to LoneStarTiger
Best adjustable on the market is from riflespeed. Makes adjustments super easy (no more allen wrench).
Rifle Speed Gas Blocks
Rifle Speed Gas Blocks

Popular
Back to top

8









