- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Need PVC Pipe help
Posted on 3/27/20 at 12:46 pm
Posted on 3/27/20 at 12:46 pm
Trying to insert a 3/4” pvc pipe into the side of a 6” pvc pipe. I have some rubber grommets used for this purpose. But I believe the wall of the 6” pipe will be too thick.
Any other suggestions on how to make this connection water right? The real hard spot is I want to be able to move the 3/4” pipe... in other words, a watertight seal, that isn’t fixed or permanent. I want to be able to slide the 3/4” pipe in and out of the 6” pipe.
Thanks!
Any other suggestions on how to make this connection water right? The real hard spot is I want to be able to move the 3/4” pipe... in other words, a watertight seal, that isn’t fixed or permanent. I want to be able to slide the 3/4” pipe in and out of the 6” pipe.
Thanks!
Posted on 3/27/20 at 1:52 pm to deuceiswild
What about using some type of PVC tee combined with a flexible pipe coupling or reducer?
Make a normal PVC tee, a stub of larger pipe, then attach the reducing coupling where your smaller pipe can slide in and out?
Something like this coming off your tee.
Make a normal PVC tee, a stub of larger pipe, then attach the reducing coupling where your smaller pipe can slide in and out?
Something like this coming off your tee.
Posted on 3/27/20 at 1:57 pm to LSUtigerME
It might take a couple of reductions. Going from 6" down to 3/4" is a big reduction.
Not sure you are going to get a watertight seal there and still expect it to be adjustable.
If you can reduce it down to 3/4", you might want to use something like this to allow adjust-ability.
Not sure you are going to get a watertight seal there and still expect it to be adjustable.
If you can reduce it down to 3/4", you might want to use something like this to allow adjust-ability.
Posted on 3/27/20 at 2:32 pm to deuceiswild
Looks like a 6"x6"x1.5" reducing T is made. I would use that and then reduce from the 1.5" down to the 3/4".
Posted on 3/27/20 at 3:52 pm to Boudreaux35
This seems the most promising suggesting. I’ve thought of such things but I’ve avoided them because 6” pvc fitting get pricy.
I’ve contacted a few online retailers about grommets that are properly sized and progress is being made. They do make grommets for this application. It’s just a matter of finding the exact size I need.
Thanks!
I’ve contacted a few online retailers about grommets that are properly sized and progress is being made. They do make grommets for this application. It’s just a matter of finding the exact size I need.
Thanks!
Posted on 3/27/20 at 5:07 pm to deuceiswild
Just out of curiosity, what is this for?
Posted on 3/27/20 at 6:01 pm to The Nino
It's for a hydroponic garden. Look up "A-Frame Hydroponic Garden" on the YouTubes.
Basically the 6" pipe runs horizontal, with several 3" holes across the top for small pots to fit into. It's capped on both ends. Water gets pumped into the 6" pipe on one end and flows to the other end. On the other end, except on the bottom, is where the 3/4" pvc drain gets inserted. How far up the big pipe you push the small pipe determines the depth of the water held in the 6" pipe.
You stack several of these 6" pipes on an A Frame. You can use 4" pipe, but the root balls have a better chance to clog the channel. Somewhere in all of this is a reservoir of water with nutrients, and all the individual drain pipes all drain back to the reservoir. A timer runs the pump intermittently. I will have 48 plants in a 24 sq ft area.
Basically the 6" pipe runs horizontal, with several 3" holes across the top for small pots to fit into. It's capped on both ends. Water gets pumped into the 6" pipe on one end and flows to the other end. On the other end, except on the bottom, is where the 3/4" pvc drain gets inserted. How far up the big pipe you push the small pipe determines the depth of the water held in the 6" pipe.
You stack several of these 6" pipes on an A Frame. You can use 4" pipe, but the root balls have a better chance to clog the channel. Somewhere in all of this is a reservoir of water with nutrients, and all the individual drain pipes all drain back to the reservoir. A timer runs the pump intermittently. I will have 48 plants in a 24 sq ft area.
Posted on 3/27/20 at 8:45 pm to deuceiswild
I would drill a 3/4" hole in the side of the 6" pvc pipe using a small hole saw or step bit. Insert your 3/4" pipe and then JB Weld the shite out out of the joint after roughing up the area with course sand paper. Those 6" pvc and fernco fittings are spendy.
Posted on 3/28/20 at 9:05 am to weadjust
This will not allow for adjustments of the 3/4” pipe. It’d be glued in place permanently
Posted on 3/28/20 at 9:23 am to deuceiswild
call me after you harvest and cure LOL
what strain?
what strain?
Posted on 3/28/20 at 9:37 am to deuceiswild
So you're doing a tiered NFT? Good news... that water will heat up and start losing o2, and bad bacteria will move in quickly. Most legit hydroponic growers use aquarium chillers to cool their reservoirs down to at least 68, if it is being recycled like nft does.
Posted on 3/28/20 at 2:16 pm to deuceiswild
Buy a 6"x2"san tee and a 2"x3/4" bushing will cost you under 40 bucks
Do it the right way
Do it the right way
Posted on 3/28/20 at 8:11 pm to deuceiswild
To do it right you will need a couple of fitting’s.
6”x6”x3” T fitting
3” to 3/4” reducer bushing fnpt
Then you just need your 3/4” pipe to have a threaded end.
When you want to seal it you just need to get a 3/4” threaded plug like this.
Although if you just need to shutoff the flow to the 3/4” it would be much easier to put a pvc ball valve on the 3/4” line so you don’t have to keep disconnecting/Capping/reconnecting.
Note: 3/4” fnpt is not the same as 3/4” hose threads for a garden hose. If you are trying to connect a garden hose be sure you get the proper garden hose threaded connection.
6”x6”x3” T fitting
3” to 3/4” reducer bushing fnpt
Then you just need your 3/4” pipe to have a threaded end.
When you want to seal it you just need to get a 3/4” threaded plug like this.
Although if you just need to shutoff the flow to the 3/4” it would be much easier to put a pvc ball valve on the 3/4” line so you don’t have to keep disconnecting/Capping/reconnecting.
Note: 3/4” fnpt is not the same as 3/4” hose threads for a garden hose. If you are trying to connect a garden hose be sure you get the proper garden hose threaded connection.
Popular
Back to top
Follow TigerDroppings for LSU Football News