- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
10x16 woodshop
Posted on 1/26/19 at 6:32 am
Posted on 1/26/19 at 6:32 am
Good Morning OB!
I am in the design stages of building a small Woodshop at my new house and wanted input on must haves!
Already have a dust collection system setup and plan on running internet out there for my cnc machine.
The roof will be open cathedral at 6/12 so I wont have too much room overhead.
Any input would be appreciated!
I am in the design stages of building a small Woodshop at my new house and wanted input on must haves!
Already have a dust collection system setup and plan on running internet out there for my cnc machine.
The roof will be open cathedral at 6/12 so I wont have too much room overhead.
Any input would be appreciated!
Posted on 1/26/19 at 6:48 am to LSURoss
I recently setup a 12x24. I’ll link a shop build from grizzly. I was able to play around with it instead of moving everything in then trying to place it. I put my table saw right in front of the door so if I get a longer board I can just open my door instead of moving my saw. Only advice is keep everything mobile in case you have to make room for a project. Grizzly workshop planner
Posted on 1/26/19 at 7:00 am to LSUfreak1459
Thanks. The only thing that will be stationary is the cnc machine. It's way to heavy to be moving around
Posted on 1/26/19 at 7:09 am to LSURoss
What size CNC? Jealous by the way.
Posted on 1/26/19 at 7:13 am to LSURoss
I have a 12×24 and its tight! Wish I would have went a little bigger. One thing that takes up a lot of room is a plywood storage rack that I built. I suggest to not do that unless you have the room and let lowes store your plywood.
Posted on 1/26/19 at 7:18 am to LSURoss
If you have the land why not build in 4’ increments and build at 12’x16’ with most building materials set up on 4’ intervals?
Posted on 1/26/19 at 7:19 am to TimeOutdoors
30x50 deck. I currently have to drag it all out into the driveway so excuse the chaotic mess. It's really fun to use
Posted on 1/26/19 at 7:20 am to wickowick
Space constraints. Also, the picture above is from the house I'm currently "renting" from a family member.
Posted on 1/26/19 at 8:24 am to LSURoss
My home woodworking shop is about 750 sq. ft. and here's a list of the big tools in it.
10 inch Radial arm saw
10 inch table saw
6 inch jointer planer
13 inch thickness planer
12 inch band saw
12 inch drill press
3 1/2 HP router mounted in a table for big shaping jobs
Then, of course, all the smaller hand tools needed to work with, mostly power tools, but a fair share of hand tools.
Oh, and you can never have enough clamps.
In all, I've probably got over $30K in tools and accessories and you will find buying something like a $250 router is nothing compared to what the bits cost.
And speaking of router bits, get the ones with 1/2 inch shanks and carbide-tipped cutters. They don't vibrate, cut like a champ and don't need sharpening near as often as regular steel bits.
ETA: The open ceiling is a good thing and allows you to store some wood on the ceiling joists to keep that out of the way.
10 inch Radial arm saw
10 inch table saw
6 inch jointer planer
13 inch thickness planer
12 inch band saw
12 inch drill press
3 1/2 HP router mounted in a table for big shaping jobs
Then, of course, all the smaller hand tools needed to work with, mostly power tools, but a fair share of hand tools.
Oh, and you can never have enough clamps.
In all, I've probably got over $30K in tools and accessories and you will find buying something like a $250 router is nothing compared to what the bits cost.
And speaking of router bits, get the ones with 1/2 inch shanks and carbide-tipped cutters. They don't vibrate, cut like a champ and don't need sharpening near as often as regular steel bits.
ETA: The open ceiling is a good thing and allows you to store some wood on the ceiling joists to keep that out of the way.
This post was edited on 1/26/19 at 11:19 am
Posted on 1/26/19 at 10:17 am to gumbo2176
Owning a cnc machine I know all about bit expenses.
Posted on 1/26/19 at 12:48 pm to gumbo2176
I will have the following
CNC Machine
12 Sliding Miter
Table Saw
Drill Press
Belt Sander
Also, assorted hand tool and bits.
All my bits and small tools are in a nice Craftsman tool box so I am not really worried about them.
I am thinking of going to the discount building place and getting some single sink cabinets and decking them for the CNC machine.
Thanks for the ideas
CNC Machine
12 Sliding Miter
Table Saw
Drill Press
Belt Sander
Also, assorted hand tool and bits.
All my bits and small tools are in a nice Craftsman tool box so I am not really worried about them.
I am thinking of going to the discount building place and getting some single sink cabinets and decking them for the CNC machine.
Thanks for the ideas
Posted on 1/26/19 at 2:04 pm to LSURoss
quote:
I am thinking of going to the discount building place and getting some single sink cabinets and decking them for the CNC machine. Thanks for the ideas
If you get in the market for tools and accessories, check out "Grizzly" for that type stuff. I've gotten a lot of my router bits and other shop accessories from them over the years. They also deal in big shop tools from the hobbyist all the way to huge commercial enterprises.
Posted on 1/26/19 at 2:18 pm to gumbo2176
Until I master this cnc machine I have been buying cheap, or even free, bits off wish.com they take a couple weeks to come in but have helped me out a bunch.
Slow, slow and slow. When you think you have it set slow enough slow it down more.
Slow, slow and slow. When you think you have it set slow enough slow it down more.
Posted on 1/26/19 at 2:21 pm to gumbo2176
Grizzly is good stuff. Their equipment that is. I have their 17” bandsaw and my grizzly g1023rl table saw us coming in Monday. They are hard to beat for the price.
Posted on 1/26/19 at 2:34 pm to LSUfreak1459
quote:
Grizzly is good stuff.
A guy I use to work with many years ago started getting into cabinet making and outfitted his whole shop with Grizzly tools and loves them. Nice machines for good prices, like you said.
Posted on 1/26/19 at 5:18 pm to LSURoss
quote:
Slow, slow and slow. When you think you have it set slow enough slow it down more
This makes sense cutting aluminum and steel but don’t slow it down too much cutting wood and other soft substrates. If you cut too slow the bit will actually burn the wood. You really need to know your bits, substrate, RPMs, and IPM to get the best cut.
quote:
Until I master this cnc machine I have been buying cheap, or even free, bits off wish.com
Worst thing you can do for a CNC is buy cheap bits or regular router bits. You have to get quality bits for the quality cuts. Once you see the difference you will never buy the cheap stuff again. Get some good quality bits and start there. You will find you can speed up and cut cleaner with the good ones. And they last three times as long.
Posted on 1/26/19 at 9:07 pm to LSURoss
quote:
Any input would be appreciated!
Plumb it for air, and get whatever size compressor you feel is adequate. The only brand I would buy is "California Air Tools", don't know how they do it, but they are oil-free, and very little noise, much less than any oiled compressor I have ben around. You could stand next to the compressor and talk on cell phone while its running with no problem, having it in your small shop will be a none issue noise wise. For a small additional charge they are available with aluminum tanks. The compressor design is supposed to last much longer than any other design.. Home Depot is not selling them on their web site, not sure if they will be available in their stores.
Posted on 1/27/19 at 1:36 am to jdavid1
have you ever used any insert type cutters on wood? I was wondering how well that might work?
Posted on 1/27/19 at 1:55 am to EA6B
quote:
don't know how they do it, but they are oil-free
I've had oilless diving compressors before. Those had Teflon pistons with leather rings, the valves were reed type, so you need to make sure that the intake air stays really clean.
I never tore one down further that the top of the cylinder, but I suspect that they use Teflon rod and crankshaft bearings
Posted on 1/27/19 at 6:28 am to EA6B
I have the California Air Tools 8 gallon compressor. It’s good and quiet.A lot of companies are coming out with the quiet compressors now. It also keeps up with a hvlp gun. I mounting an air hose reel on the ceiling to save space on the walls.
Popular
Back to top
Follow TigerDroppings for LSU Football News