- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Undermount sink fell, how to lift and hold in place
Posted on 7/21/23 at 5:44 pm
Posted on 7/21/23 at 5:44 pm
Came home to find my undermount sink in kitchen fell. Suggestions on how to lift and hold in place.
Double sink and granite counter top if that makes a differnce.
Double sink and granite counter top if that makes a differnce.
Posted on 7/21/23 at 5:51 pm to WPBTiger
Cinder blocks, 2x4s, bottle jack, etc.
Posted on 7/21/23 at 6:00 pm to WPBTiger
Just have her lay flat and exhale.
Posted on 7/21/23 at 6:03 pm to WPBTiger
How was it held in place?
Stainless?
Stainless?
Posted on 7/21/23 at 6:31 pm to ItzMe1972
quote:
How was it held in place?
Looks like silicone.
quote:
Stainless?
Yes
Posted on 7/21/23 at 6:50 pm to WPBTiger
2x4 laid across countertop, bar clamps thru drains.
Posted on 7/21/23 at 7:09 pm to WPBTiger
Posted on 7/21/23 at 9:18 pm to WPBTiger
Clean the silicone from the the top of the sink. Apply new silicone and lift sink and secure by sliding a 1x2 in the from and back and pocket screw into the sidewalls of the cabinet on both sides.
Posted on 7/21/23 at 10:47 pm to WPBTiger
Need two lengths of 2x4, two pieces of long enough 3/8" all-thread, large washers, and nuts. Basically you just need run the all-thread through the drain openings and into the 2x4's to create a clamp. This works far better than using beam or pipe clamps, also forget using silicone to adhere the sink to the granite, it will fail again, you need to use construction adhesive like PL Premium or two-part gun-grade epoxy. I also use epoxy mounted studs to reinforce after the initial work as set. Go back with silicone to fill the inside seam but never use it as a primary adhesive for an undermount of any type. I do this repair several times a year, not difficult but also not one you want to do every few years either.
Posted on 7/22/23 at 12:21 pm to Clames
Thanks for the suggestions.
I had originally thought of the bottle jack as I have used that method in the past to hang cabinets.
After reading through the different suggestions, I went with Clames' method of using threaded rods and 2x4s. This worked like a champ
I also used construction adhesive as was suggested as opposed to silicone for the attachment.
I also took tigerfan311's advice and ordered the Never Fall Complete Sink Repair. It arrives tomorrow and that should give the construction adhesive a little of 24 hours to cure.
Between the two suggestions used/to be used, this sink should no longer fall again.
I wanted to use awestruck's suggestion but she was not available.
I had originally thought of the bottle jack as I have used that method in the past to hang cabinets.
After reading through the different suggestions, I went with Clames' method of using threaded rods and 2x4s. This worked like a champ
I also used construction adhesive as was suggested as opposed to silicone for the attachment.
I also took tigerfan311's advice and ordered the Never Fall Complete Sink Repair. It arrives tomorrow and that should give the construction adhesive a little of 24 hours to cure.
Between the two suggestions used/to be used, this sink should no longer fall again.
I wanted to use awestruck's suggestion but she was not available.
This post was edited on 7/22/23 at 12:24 pm
Posted on 7/22/23 at 8:59 pm to Shorty_price
quote:
2x4 laid across countertop, bar clamps thru drains.
This
Popular
Back to top
Follow TigerDroppings for LSU Football News