cheezag03

thanks to all for the info. I'm not as worried about top-end speed unless what drives that translates to getting in and out of shallow boggy areas. Or i need to look for a 25hp mud motor with high low-end torque...

Anybody every run a 25hp surface drive or long tail on a 17x50 .125 flat bottom aluminum? How much better would a surface drive push the boat than a long tail? Here is what I'm trying to do. Looking to sell a 15 yr old 18' CC fiberglass tunnel hull with 150 hp outboard to get aluminum flat ...

is that 600lb rating the tongue weight? How big of a boat and trailer do you think one person could move with one of those?...

Understood.....thanks....

What makes a mud boat then? Jet drive, inboard, etc? A SwampShark? I just assumed any flat bottomed aluminum with an air cooled motor was a mud boat...

Is this considered mud boat or surface drive? [img]http://prodigyboats.com/wp-content/uploads/2014/08/IMG_5687.JPG[/img] [img]http://gatortraxboats.com/wp-content/uploads/2016/11/jbarnes1best.jpg[/img] Anybody ever change out their motor by season? Seems like if you kept it all tiller woul...

pardon my ignorance, but I thought you put a surface drive outboard on a mud boat? Anybody ever done interchangeable motors on their duck boat? I'm thinking about getting a gator trax type custom build and putting a jack plate on there with a 40-50 hp tiller water cooled and swapping out with a ...

any waterfowl hunting in Bayou La Croix Preserve?...

I've done three ways in order of best to worst: 1. Debone and cut up into about half inch to inch pieces. Add to chili when you put in your chili plate ground meat after cooking down the trinity. I cooked in cast iron dutch oven and let my chili simmer for a good while with the lid on. You ge...

from looking at your other posts I'm guessing Chambers County? Anahuac NWR gave me an asswhooping Saturday when I picked a pond far off the road never having scouted the refuge. Thought it would be a solid ground walk out so I took a big bag of dekes and a bucket and never made it the 700 yds ...

I didn't know Majek made it out of Texas. Makes sense for shallow water...

Apparently Frio has one [img]https://www.instagram.com/p/BW_YJexli2N/?taken-by=kaceebones[/img] [link=(https://www.instagram.com/p/BW_YJexli2N/?taken-by=kaceebones)]Frio[/link]...

quote: [quote]I can't get firm skin on smoked chicken to save my life. This is my issue too. The chicken skin turns out too rubbery. And this is after I leave it sitting uncovered overnight and try to dry the skin off before putting it on. I don't do whole chickens enough to really worry about...

I would diversify my holdings. A place on the Devil's River [link=(http://www.landandfarm.com/property/6600_Acres_in_Val_Verde_County-377397/)]nice little ranch[/link] - deer, audad, some quail and river float fishing Floating cabin on Baffin House on stilts in West Galveston Bay - permit h...

[quote]in houston..you can leave river oaks, sit in ungodly traffic and sweat in the 101 degree 111% humidity and swear the concrete never ends as you try to find anything of value to do outdoors[/quote] You leave River Oaks to the NE and its a park on the bayou for the next 3-4 miles until you r...

the melons on that broad......good god almighty! :nana:...

Did you have brisket and ribs at Pinkerton's or were looking for chicken wings? I like to drink a couple Shiner's at Alice's Tall Texan and then bounce to Pinkerton's for $1 beers on Thursdays and get some brisket and ribs for the casa. At 36 I would get a Heights place and rent your garage apar...

I thought about buying these plans and trying to build [img]http://bateau.com/prodimages/SK14.jpg[/img] [link=(http://bateau.com/proddetail.php?prod=SK14)]Flat Skiff plans[/link]...

Maybe something like this? [link=(http://www.southfloridaboatcenter.com/)]HCraft boats[/link]...

[quote]quote: You have the right to an attorney. If you cannot afford an attorney, one will be provided for you. Sounds like he could afford an attorney rather than bailing out.[/quote] Hard to get high and knock up bitches on the taxpayer's dime behind bars...