- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Any 3d printer firmware gurus
Posted on 1/14/23 at 3:18 pm
Posted on 1/14/23 at 3:18 pm
I am in dire need of some firmware help. Any baws here a Jedi at it?
3
Posted on 1/14/23 at 6:48 pm to SauceBawse
There’s a ton of chat about them in the FB groups I’m in, but I haven’t dabbled with it yet.
Posted on 1/14/23 at 7:00 pm to SauceBawse
quote:
I am in dire need of some firmware help. Any baws here a Jedi at it?
What printer?
Posted on 1/14/23 at 8:51 pm to SauceBawse
Marlin?
Posted on 1/15/23 at 9:03 am to CP3
This post was edited on 1/15/23 at 12:14 pm
Posted on 1/15/23 at 12:14 pm to SATNIGHTS
Ender 3 Pro; BTT E3V3; CR Touch; TFT35 LCD, TH3D Firmware
Where to start. It all began with installing the BTT E3V3 board and TFT Display. I installed the nightly Marlin firmware and when I would auto home the x and y would home correctly but the CR Touch would grind into my bed. Switched to the TH3 Firmware and still have the same issue. I made a few tweaks to the firmware and now the CR Touch drops the pin 3 times and then the TFT display give me an error.
I think all of my wiring looks good except for my red wire which I need to re-terminate but its connected regardless. Thoughts on what I am doing wrong? In the TH3D firmware they do not have an Ender 3 Pro option so I chose the Ender 3.....
Where to start. It all began with installing the BTT E3V3 board and TFT Display. I installed the nightly Marlin firmware and when I would auto home the x and y would home correctly but the CR Touch would grind into my bed. Switched to the TH3 Firmware and still have the same issue. I made a few tweaks to the firmware and now the CR Touch drops the pin 3 times and then the TFT display give me an error.
I think all of my wiring looks good except for my red wire which I need to re-terminate but its connected regardless. Thoughts on what I am doing wrong? In the TH3D firmware they do not have an Ender 3 Pro option so I chose the Ender 3.....
Posted on 1/15/23 at 5:21 pm to SauceBawse
https://www.makenprint.uk/3d-printing/3d-firmware-guides/marlin/consolidated-marlin-guide/
Select your board, equipment, etc. and follow the guide to compile Marlin. This is what I did for the same setup minus the LCD.
Select your board, equipment, etc. and follow the guide to compile Marlin. This is what I did for the same setup minus the LCD.
Posted on 1/15/23 at 5:51 pm to guedeaux
I did similar to this when I changed my motherboard after installing EZabl. You build your firmware and install it. Eazy enough and I never had problems.
Posted on 1/16/23 at 6:11 am to SauceBawse
Yo I wrote my own Marlin code for my custom machines. I chased a fricking missing backlash for two weeks during auto leveling once. It's that picky.
What "tweaks did you make" to the firmware? And paste your error code please.
What "tweaks did you make" to the firmware? And paste your error code please.
Posted on 1/16/23 at 9:12 am to DJNOS1978
So yesterday I switched back to the stock Creality board and used the nightly Marlin build. This time no errors but the same issue. When I auto home X,Y are fine and then the nozzle does not retract when the CR Touch pin touches the bed resulting in the nozzle grinding into the bed. I ordered a replacement wire from Creality last night as I read that sometimes the wires can cause issues, but other than that I am at a loss. I have a brand new BTT board and display sitting here now waiting for me to figure out the issue before I swap back in. Perhaps I should troubleshoot with them back in instead of fixing and then swapping hardware again.
Posted on 1/16/23 at 10:01 am to SauceBawse
Thoughts on something in marlin that would cause this?
Posted on 1/16/23 at 11:31 am to SauceBawse
Your settings in autolevel in firmware. Copy and paste the part of Marlin from the bed leveling. Sounds like you didn't change anything in the firmware. When I changed from a simple limit switch for my nozzle height to an inductor probe there was quite a change that had to take place in firmware. False to true for autolevel and Z offset. There is also a place in config files you need to change. I don't know that particular piece of hardware but your problem is all firmware.
Posted on 1/16/23 at 11:55 am to DJNOS1978
//#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR
#define AUTO_BED_LEVELING_BILINEAR
//#define AUTO_BED_LEVELING_UBL
//#define MESH_BED_LEVELING
This post was edited on 1/16/23 at 11:57 am
Posted on 1/16/23 at 11:57 am to SauceBawse
Am I supposed to turn anything else on in that section?
Posted on 1/16/23 at 11:58 am to SauceBawse
I'm not familiar with the EXACT type of component that CL touch is. But if that's the one they suggest then you only need that one.
Posted on 1/16/23 at 12:00 pm to SauceBawse
But there a lot more options in Marlin for autolevel than just that section. That's just to turn on the feature. You have many more settings to change.
Posted on 1/17/23 at 6:49 pm to DJNOS1978
Well I am compiling from scratch now. Want to walk me through it?
Posted on 1/18/23 at 6:23 am to SauceBawse
Bruh. Why? You were almost there
Posted on 1/18/23 at 10:15 am to DJNOS1978
I went back and swapped the BTT E3V3 board and TFT screen back in. Still the same issue of the nozzle grinding into the bed so I figured maybe start fresh???
Posted on 1/18/23 at 12:55 pm to SauceBawse
I thought you meant you were writing your own code. Do you have any error codes in the script that shows?
I need to see the entire autolevel code.
I need to see the entire autolevel code.
Page 1 of 2
Popular
Back to top
Follow TigerDroppings for LSU Football News