- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Resin/Epoxy bar top help
Posted on 2/4/19 at 8:48 am
Posted on 2/4/19 at 8:48 am
Has anyone done their own resin/epoxy bar top or coffee table and had success. If so please recommend the brand you went with and how difficult was it. I want to do a live edge cypress coffee table and looking for whatever help i can get other than youtube stuff i have seen. TIA
Posted on 2/4/19 at 9:22 am to tigerrage08
Is there a reason you want epoxy instead of Polly or more traditional oil based finish ?
Posted on 2/4/19 at 9:31 am to Chuckd
quote:
Is there a reason you want epoxy instead of Polly or more traditional oil based finish ?
I'm in the process of building my own bar top for my porch. I looked into a resin, but decided on using Helmsman SPAR instead. I'm interested in your decision for resin as well, because I am new to wood working/furniture building.
Posted on 2/4/19 at 10:10 am to tigerrage08
glaze coat
I just finished up a little coffee table project last week. This is the stuff I used. First time trying it. It wasn't too difficult, just mix the two parts together and pour it. You can order pigment colors off of amazon to mix it in. Clamp down the piece of wood air tight so it does not leak out of the bottom. When this stuff fully cures, it gets harder than woodpecker lips.
I just finished up a little coffee table project last week. This is the stuff I used. First time trying it. It wasn't too difficult, just mix the two parts together and pour it. You can order pigment colors off of amazon to mix it in. Clamp down the piece of wood air tight so it does not leak out of the bottom. When this stuff fully cures, it gets harder than woodpecker lips.
This post was edited on 2/4/19 at 12:01 pm
Posted on 2/4/19 at 10:22 am to Chuckd
no particular reason. I am good with a poly type finish. I just want a nice thick and glossy protective coating.
Posted on 2/4/19 at 10:25 am to Bamawaterfowl
The tip about sealing the bottom of any gaps is a good one. It will run right through unless you stop it.
I used the glaze coat as well. It took almost a week to cure to the point I could sand it, which is longer than the directions say. But it worked well in the end, and is cheaper than the West System stuff.
I used the glaze coat as well. It took almost a week to cure to the point I could sand it, which is longer than the directions say. But it worked well in the end, and is cheaper than the West System stuff.
Posted on 2/4/19 at 10:27 am to Chuckd
quote:because resin is way more resilient than poly or spar.
Is there a reason you want epoxy instead of Polly or more traditional oil based finish ?
This post was edited on 2/4/19 at 10:27 am
Posted on 2/4/19 at 10:35 am to tigerrage08
I made a table top out of pecky cypress paneling, and used epoxy resin to fill in the holes. I kept it clear so you could still see into the holes.
I used East Coast Resin epoxy, I think I had about 50 or 60 bucks in it for a one gallon kit. It doesn't prevent bubbles like some of the more expensive stuff, but if you don't pour too much all at once a grill/candle lighter will take care of bubbles. A little butane torch would be even better.
If you have cracks or holes, tape the underside of your work piece with some painter's tape or else you're going to epoxy the table to your work bench. Then do a light pour to seal those holes and let it cure for 24 hours before you do the real pour. That way you aren't just dumping stuff out the bottom to run out everywhere.
I used East Coast Resin epoxy, I think I had about 50 or 60 bucks in it for a one gallon kit. It doesn't prevent bubbles like some of the more expensive stuff, but if you don't pour too much all at once a grill/candle lighter will take care of bubbles. A little butane torch would be even better.
If you have cracks or holes, tape the underside of your work piece with some painter's tape or else you're going to epoxy the table to your work bench. Then do a light pour to seal those holes and let it cure for 24 hours before you do the real pour. That way you aren't just dumping stuff out the bottom to run out everywhere.
Posted on 2/4/19 at 11:54 am to CarRamrod
(no message)
This post was edited on 10/19/21 at 2:52 pm
Posted on 2/4/19 at 12:05 pm to tigerrage08
Posted on 2/4/19 at 2:15 pm to Bamawaterfowl
Posted on 2/4/19 at 5:39 pm to tigerrage08
I had no experience with it and tried to do my bar top. I made a mess out of everything with it. I ended up getting it decent, but it took extra coats which got expensive
You might want to consider paying someone who knows what they are doing to do it. Those guys on YouTube make it look very easy, but it's tricky to work with.
Also the temperature has to be within a certain range for it to cure properly.
You might want to consider paying someone who knows what they are doing to do it. Those guys on YouTube make it look very easy, but it's tricky to work with.
Also the temperature has to be within a certain range for it to cure properly.
Posted on 2/4/19 at 9:27 pm to tigerrage08
We used whatever brand Lowes sells, follow the directions completely it it will turn out good.
Posted on 2/5/19 at 5:48 am to Interweb Cowboy
Posted on 2/5/19 at 7:54 am to tigerrage08
[/img]
Not perfect by any means but I like it.
Not perfect by any means but I like it.
Posted on 2/5/19 at 11:18 am to Bamawaterfowl
It will take twice as much poly as epoxy. Shoot me an email and I will send you some pics of a bar I built in my mancave. I used epoxy and it was relatively easy and turned out great. Not to mention, epoxy is going to hold up a lot better than most anything else you use if it is going on wood.
Popular
Back to top
Follow TigerDroppings for LSU Football News