- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Can I replace this bathtub drain?
Posted on 3/20/19 at 7:59 pm
Posted on 3/20/19 at 7:59 pm
Is it something I can DIY?
If not, how much does a plumber cost to do this?
If not, how much does a plumber cost to do this?
Posted on 3/20/19 at 8:06 pm to deeprig9
Looks like it. Lowe's makes a tool that goes in the drain and you unscrew it.
Posted on 3/20/19 at 8:15 pm to nugget
quote:
Lowe's makes a tool that goes in the drain and you unscrew it.
They sell a few, the one that looks like a big screw extractor works the best but that's relative. If it's pretty old and water has corroded the threads then you are in for some fun. Get a good hacksaw blade and an open handle for it when you get the extractor tool.
Posted on 3/20/19 at 8:19 pm to deeprig9
Get a dumbell tub wrench and hope either the tub if its cast iron or the drain isnt rusted. If that is a fiberglass tub you should be able to for sure get it out.You could buy it and return it if you fear you are going to break it.
Posted on 3/20/19 at 10:07 pm to deeprig9
Easy. Home Depot carries a husky brand extractor. It’s a heavy wad of metal with etching on the outside that grips the inside of the drain like teeth. So you beat this tool into drain with a hammer. Not too strong, just tap it until it’s good and bitten into the drain.
Then you attach a 1/2 wratchet to the tool and start turning. It’ll loosen right up.
Then you attach a 1/2 wratchet to the tool and start turning. It’ll loosen right up.
Posted on 3/20/19 at 10:39 pm to RiseUpATL
But I have to get a new drain in too. That's the other half of the equation.
Posted on 3/20/19 at 10:53 pm to deeprig9
Yes, it is manageable to do this yourself...I did one of mine a few years back. It was kind of a pain in the arse, but worth it because I saved a couple of hundred bucks.
Posted on 3/21/19 at 12:29 pm to deeprig9
quote:
But I have to get a new drain in too. That's the other half of the equation.
It's a P-trap below it. You can just replace the top drain for aesthetics without messing with the actual P trap below.
Posted on 3/21/19 at 8:15 pm to idlewatcher
quote:
It's a P-trap below it. You can just replace the top drain for aesthetics without messing with the actual P trap below.
I guess my question is if I have to tear the shite out of it to get the old one off, the new one isn't going to just slip right in, the new one will have to get all jacked up just to wrench it into place?
Educate me.
This post was edited on 3/21/19 at 8:16 pm
Posted on 3/21/19 at 8:27 pm to deeprig9
Your house have a slab or crawl space?
Posted on 3/21/19 at 9:06 pm to deeprig9
It screws in. Try cleaning the female threads after you get the old one out. If you're lucky, the new one will just screw in. If not, you're gonna have to get under the tub and replace the fitting it screws into. If you have a valve access panel, that would be a good place to look for what you'd need to replace
Posted on 3/21/19 at 9:17 pm to weadjust
Upstairs bathtub.
No access to underneath without cutiing up kitchen ceiling.
No access to underneath without cutiing up kitchen ceiling.
Posted on 3/21/19 at 9:55 pm to deeprig9
Ever heard of YouTube? Plenty of videos on this. I just replaced mine in the house I just bought because the old one’s top was broken. The drains themselves simply screw into the pipe under the tub.
You take that tool I referred to up a few posts. Jam it into the old drain, then grab your 1/2 inch drive ratchet and unscrew the old drain from the pipe.
Clean the threads in the pipe and around where the old drain was. There will/should be dried Plummer’s putty all in there.
Next take your new drain. Some new drains come with a threaded adapter if you have a wider pipe inlet. If you don’t need the adapter discard it.
Take some new Plummer’s putty. Just a ball of it about the size of a ping pong ball and roll it between your palms and create a snake. Take that and wrap it under the new drains lip and lightly press it in place to form a seal.
Take the tool used to remove the old drain. Carefully put it in the new drain (you don’t want to scuff it up) then place the new drain into place and start to hand thread being careful not to cross thread. When you can’t hand tighten any longer put your ratchet back on the tool that ms jammed in the new drain and click your ratchet to tighten and start to screw it in. Screw it until the Plummer’s putty starts to squeeze out from under the drain lip and the tub and you feel you have tightened it enough. Do not over tighten. Take your finger and remove the excess putty that squeezed out. All done.
You take that tool I referred to up a few posts. Jam it into the old drain, then grab your 1/2 inch drive ratchet and unscrew the old drain from the pipe.
Clean the threads in the pipe and around where the old drain was. There will/should be dried Plummer’s putty all in there.
Next take your new drain. Some new drains come with a threaded adapter if you have a wider pipe inlet. If you don’t need the adapter discard it.
Take some new Plummer’s putty. Just a ball of it about the size of a ping pong ball and roll it between your palms and create a snake. Take that and wrap it under the new drains lip and lightly press it in place to form a seal.
Take the tool used to remove the old drain. Carefully put it in the new drain (you don’t want to scuff it up) then place the new drain into place and start to hand thread being careful not to cross thread. When you can’t hand tighten any longer put your ratchet back on the tool that ms jammed in the new drain and click your ratchet to tighten and start to screw it in. Screw it until the Plummer’s putty starts to squeeze out from under the drain lip and the tub and you feel you have tightened it enough. Do not over tighten. Take your finger and remove the excess putty that squeezed out. All done.
Popular
Back to top
Follow TigerDroppings for LSU Football News