- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
re: Post your Woodworking Projects
Posted on 5/2/19 at 12:39 pm to idlewatcher
Posted on 5/2/19 at 12:39 pm to idlewatcher
I am far from a master woodworker.
I know that most wouldn’t believe, but I picked up woodworking about one full year ago. I have been around it as my father, grand and great grandfather were all master and accomplished wood carvers.
It started as a simple project my wife asked for and I was sick and damn tired of her asking my father in-law for the help.
It turned into a quick whirlwind of passion for woodwork.
Every piece I post has been done within the past year.
One year ago I owned zero. ZERO tools. I now have a full blown workshop minus a couple of specialty tools. I have 1-2 commissioned pieces that stay on my book and I find time for quirky little pieces like the LSU board.
As for the T and L not bleeding. It is all about your prep. You have to have a plan. Have a specific task each time you grab a tool. No winging it. Write things down in a notebook or on your bench top.
For that specific project I put down my LSU logo onto the wood of choice with sticky paper. I then trimmed it with an exacto knife. I routed out the LSU portion and poured its epoxy; leaving the “tigers” behind. I then exacto cut around the tigers portion. — a good tip for inlays to work is to use a chisel or knife to cut your edges. This will cause your router to give you a small “notice” when you get to that cut mark. It essentially is a feeling of ease or relief and you then know your at your edge. I always finish my routes edges with chisels. Never sand. Sanding will produce a rounded edge. You want a strict sharp flat edge.
Back to the piece, I routed the Tigers and went very slow. If your router has speed settings 1-6 let’s say.. use 2-3. Have a steady hand and route until you see no wood and all epoxy where the LSU and tigers will meet. Once done simply pour again into the tigers and your done.
Remember, cleanliness while pouring isn’t imperative if you put good proper hard cut chisled edges. When you sand it down afterwards it’ll sand to where that fine popped line is and give you the finish you see in the photo.
![](https://i.imgur.com/pkllrQb.jpg)
I know that most wouldn’t believe, but I picked up woodworking about one full year ago. I have been around it as my father, grand and great grandfather were all master and accomplished wood carvers.
It started as a simple project my wife asked for and I was sick and damn tired of her asking my father in-law for the help.
It turned into a quick whirlwind of passion for woodwork.
Every piece I post has been done within the past year.
One year ago I owned zero. ZERO tools. I now have a full blown workshop minus a couple of specialty tools. I have 1-2 commissioned pieces that stay on my book and I find time for quirky little pieces like the LSU board.
As for the T and L not bleeding. It is all about your prep. You have to have a plan. Have a specific task each time you grab a tool. No winging it. Write things down in a notebook or on your bench top.
For that specific project I put down my LSU logo onto the wood of choice with sticky paper. I then trimmed it with an exacto knife. I routed out the LSU portion and poured its epoxy; leaving the “tigers” behind. I then exacto cut around the tigers portion. — a good tip for inlays to work is to use a chisel or knife to cut your edges. This will cause your router to give you a small “notice” when you get to that cut mark. It essentially is a feeling of ease or relief and you then know your at your edge. I always finish my routes edges with chisels. Never sand. Sanding will produce a rounded edge. You want a strict sharp flat edge.
Back to the piece, I routed the Tigers and went very slow. If your router has speed settings 1-6 let’s say.. use 2-3. Have a steady hand and route until you see no wood and all epoxy where the LSU and tigers will meet. Once done simply pour again into the tigers and your done.
Remember, cleanliness while pouring isn’t imperative if you put good proper hard cut chisled edges. When you sand it down afterwards it’ll sand to where that fine popped line is and give you the finish you see in the photo.
![](https://i.imgur.com/HFMdJET.jpg)
![](https://i.imgur.com/ukwbNkI.jpg)
![](https://i.imgur.com/aN1ekeT.jpg)
![](https://i.imgur.com/cfHROXf.jpg)
![](https://i.imgur.com/Hy40BfK.jpg)
![](https://i.imgur.com/pkllrQb.jpg)
This post was edited on 5/2/19 at 12:45 pm
Posted on 5/2/19 at 2:56 pm to TIGERBAIT84
You read my mind about the photos, was just about to ask if you had any.
Appreciate the explanation of how you went about it. Makes sense when you can see it layed out step by step.
This is referring to pre-Routing yea? As in after you've cut out the template.
Appreciate the explanation of how you went about it. Makes sense when you can see it layed out step by step.
quote:
a good tip for inlays to work is to use a chisel or knife to cut your edges
This is referring to pre-Routing yea? As in after you've cut out the template.
Posted on 5/7/19 at 3:04 pm to TIGERBAIT84
What epoxy do you use and where do you get it?
Also what router bit did you use that the exacto knife or chisel helped with?
Im new to routers so a bit more of an explanation or a YouTube video would be nice.
Good work![](https://images.tigerdroppings.com/Images/Icons/Iconcheers.gif)
Also what router bit did you use that the exacto knife or chisel helped with?
Im new to routers so a bit more of an explanation or a YouTube video would be nice.
Good work
![](https://images.tigerdroppings.com/Images/Icons/Iconcheers.gif)
Popular
Back to top
![logo](https://images.tigerdroppings.com/images/layout/TDIcon.jpg)