Page 1
Page 1
Started By
Message

Kitchen faucet pulsing when on hot water

Posted on 1/14/21 at 5:45 pm
Posted by fatboydave
Fat boy land
Member since Aug 2004
17979 posts
Posted on 1/14/21 at 5:45 pm
WTF is causing that? It is a little over one year old and only starts pulsing when on hot water side. It doesn't do it constantly. Just when the water starts getting hot. The faucet is a single lever faucet. The water comes out but makes a noise and pulses/sputters when the water comes out.
This post was edited on 1/14/21 at 5:52 pm
Posted by TU Rob
Birmingham
Member since Nov 2008
12740 posts
Posted on 1/14/21 at 6:39 pm to
Just started doing it? How old is the water heater? Might need sediment cleaned out of it. Any other faucets doing it or just the kitchen? What type of pipe is the supply line? Old copper can get crusty inside after a while.
Posted by fatboydave
Fat boy land
Member since Aug 2004
17979 posts
Posted on 1/14/21 at 7:34 pm to
Started about a month ago. Water heater is about 12 years old. No other faucets affected. Not sure of the suply line since its behind the cabinet wall.

How do I check for sediment? In the cartridge?

Posted by HonoraryCoonass
Member since Jan 2005
18075 posts
Posted on 1/14/21 at 8:30 pm to
I’d change the cartridge, and see what happens. Newer kitchen fixtures usually have a lifetime warranty, so you can probably get a replacement cartridge for free from the manufacturer.
Posted by TU Rob
Birmingham
Member since Nov 2008
12740 posts
Posted on 1/14/21 at 8:43 pm to
quote:

Started about a month ago. Water heater is about 12 years old. No other faucets affected. Not sure of the suply line since its behind the cabinet wall.

How do I check for sediment? In the cartridge?


Can you access any of the water lines? Or is it on a slab? Ours are all visible in the basement, and the kitchen is the first faucet on the water lines. Just a shot in the dark, but if you replaced the faucet about a year ago, the water had to have been shut off and drained from the lines. Could be that cutting the water back on stirred up sediment in the 12 year old water heater, and when the lines were filling back up it might have sent some and got there first.

You can check the water heater for sediment by hooking up a hose to the valve near the bottom and turning that handle, or like mine, which has a slotted opening, use a flat headed screwdriver to turn it to open and check what the water looks like coming out of the hose. If you can't easily get a hose run to outside, you can always use a 5 gallon bucket and catch what is coming out. Should know right away if the water is cloudy. Let it run until the water is clear, and then a little more.

Another thought, is there a separate water valve and a small hose running from that to the faucet? You can take that off and see if that little supply hose is clogged up.
Posted by Coater
Madison, MS
Member since Jun 2005
33064 posts
Posted on 1/14/21 at 9:11 pm to
Agree regarding cartridge

They’re about $30 typically

I changed one out yesterday in my kids’ tub because the pressure had gone down significantly over that last year. Instant fix. Hard water can contribute to them getting clogged
Posted by Martini
Near Athens
Member since Mar 2005
48853 posts
Posted on 1/14/21 at 9:51 pm to
quote:

Started about a month ago. Water heater is about 12 years old. No other faucets affected. Not sure of the suply line since its behind the cabinet wall.



You are on borrowed time with a 12 year old water heater. Likely it has rust in it and sediment. 12 years is pushing it.
Posted by fatboydave
Fat boy land
Member since Aug 2004
17979 posts
Posted on 1/15/21 at 8:19 am to
I'll check the cartridge for sediment.

Not looking forward to water heater replacement in the attic.
first pageprev pagePage 1 of 1Next pagelast page
refresh

Back to top
logoFollow TigerDroppings for LSU Football News
Follow us on Twitter, Facebook and Instagram to get the latest updates on LSU Football and Recruiting.

FacebookTwitterInstagram