- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Condensation shorting A/C Handler in attic
Posted on 9/22/17 at 1:58 pm
Posted on 9/22/17 at 1:58 pm
The control board inside of our air handler in the attic keeps getting condensation on it.. It is one of those "builders units", a Goodman/Amana, that looks like the one pictured at this link:
LINK
When the water droplets get on the board just right, it starts to short out relays, etc., and the unit will start as normal, run for 2-3 seconds, then stop. If we're not home to notice it, it will do this into infinity -- which i'm sure means it's already taken 5 years off its lifespan.
They have the unit installed on its side, and so the cold air actually leaves the unit BEHIND the metal panel that the controls are mounted on.
Any ideas on how to keep this from happening?
LINK
When the water droplets get on the board just right, it starts to short out relays, etc., and the unit will start as normal, run for 2-3 seconds, then stop. If we're not home to notice it, it will do this into infinity -- which i'm sure means it's already taken 5 years off its lifespan.
They have the unit installed on its side, and so the cold air actually leaves the unit BEHIND the metal panel that the controls are mounted on.
Any ideas on how to keep this from happening?
2
Posted on 9/22/17 at 1:59 pm to jmcwhrter
quote:install attic fan with a controller to move heat out of the attic to limit the temperature gradient causing the condensate
Any ideas on how to keep this from happening
Posted on 9/22/17 at 2:13 pm to jmcwhrter
seal any openings - warm moist air in the attic is getting into the unit and condensing
if i had to guess the rubber grommets that seal around the piping into the units were not installed properly or a dry rotted
or
either an electrical knockout is missing and not used or the electrician didnt seal the penetration correctly.
if those are not the case feel around for air flowing out of panel seams.
From looking at the unit you linked, this is a draw-through fan configuration (which means the fan is located up stream of the coil section and pulls the air across the coil) because the air handling section before the coil is in a negative pressure, it will actually suck in attic air if there are leaks in to the cabinet.
EDIT:
looking at the installation manual in the "documentation" tab link, it appear the control section is on the top of the unit and it has the electrical knockouts in that cabinet section. i would look for leaks at the electrical penetrations first.
if i had to guess the rubber grommets that seal around the piping into the units were not installed properly or a dry rotted
or
either an electrical knockout is missing and not used or the electrician didnt seal the penetration correctly.
if those are not the case feel around for air flowing out of panel seams.
From looking at the unit you linked, this is a draw-through fan configuration (which means the fan is located up stream of the coil section and pulls the air across the coil) because the air handling section before the coil is in a negative pressure, it will actually suck in attic air if there are leaks in to the cabinet.
EDIT:
looking at the installation manual in the "documentation" tab link, it appear the control section is on the top of the unit and it has the electrical knockouts in that cabinet section. i would look for leaks at the electrical penetrations first.
This post was edited on 9/22/17 at 2:19 pm
Page 1 of 1
Popular
Back to top
Follow TigerDroppings for LSU Football News