- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
re: Official WINK HUB Home Automation thread
Posted on 1/29/16 at 7:35 am to CAD703X
Posted on 1/29/16 at 7:35 am to CAD703X
Yes, the other repaired just fine. Lights solid for 5 seconds, then a short flash and it paired. This light blinks for about 10 seconds which is different than the others. I assume it means something.
Eta: I'll try again tonight. I was doing it all in one step which worked for two of the switches.
Eta: I'll try again tonight. I was doing it all in one step which worked for two of the switches.
This post was edited on 1/29/16 at 7:38 am
Posted on 1/29/16 at 9:09 am to mctiger1985
Zwave devices I had to reset and process
- leviton dimmer switch:
1. push top of switch and pull up on bottom (makes bottom come completely out of wall) so it's reset
2. Hit exclusion mode on wink (so it will send unpair signal to switch) - success is a breuf green flash on wink
3. Hit inclusion mode and push switch (doesn't matter where) wait for green flash and its back
4. Find generic "light bulb" under lights and rename
- GE dimmer switch
1. Grab the tiny tab under switch button and pull (I used my fingernails) so it comes out about 1/8 inch for 5 seconds then push back in so it's reset
2. Hit exclusion mode on wink (so it will send unpair signal to switch) - success is a breuf green flash on wink
3. Hit inclusion mode and push switch TWICE (doesn't matter where) wait for green flash and its back
4. Find generic "light bulb" under lights and rename
- schlage lock
1. Open door extend deadbolt manually
2. Put wink into exclusion mode - should be near lock so you can observe it
3. Hit schlage button, enter 6 digit security code then 0 and you should get green checkmark on keypad and wink should flash green briefly.
4. Put wink in inclusion mode, repeat #3 above
5. Lock should appear in wink menu however DO NOT attempt to use it or rename it for a good 5 minutes while the lock "chats" with wink and attempts to sync all it's statuses.
6. Try hitting lock/unlock in wink. If nothing happens hit it again because wink isn't clear if it's unlocked or locked until you go through the cycle at least once.
7. User codes may come back but without the names so they're useless. Delete codes and enter them again.
Tapt instructions are still coming.
- leviton dimmer switch:
1. push top of switch and pull up on bottom (makes bottom come completely out of wall) so it's reset
2. Hit exclusion mode on wink (so it will send unpair signal to switch) - success is a breuf green flash on wink
3. Hit inclusion mode and push switch (doesn't matter where) wait for green flash and its back
4. Find generic "light bulb" under lights and rename
- GE dimmer switch
1. Grab the tiny tab under switch button and pull (I used my fingernails) so it comes out about 1/8 inch for 5 seconds then push back in so it's reset
2. Hit exclusion mode on wink (so it will send unpair signal to switch) - success is a breuf green flash on wink
3. Hit inclusion mode and push switch TWICE (doesn't matter where) wait for green flash and its back
4. Find generic "light bulb" under lights and rename
- schlage lock
1. Open door extend deadbolt manually
2. Put wink into exclusion mode - should be near lock so you can observe it
3. Hit schlage button, enter 6 digit security code then 0 and you should get green checkmark on keypad and wink should flash green briefly.
4. Put wink in inclusion mode, repeat #3 above
5. Lock should appear in wink menu however DO NOT attempt to use it or rename it for a good 5 minutes while the lock "chats" with wink and attempts to sync all it's statuses.
6. Try hitting lock/unlock in wink. If nothing happens hit it again because wink isn't clear if it's unlocked or locked until you go through the cycle at least once.
7. User codes may come back but without the names so they're useless. Delete codes and enter them again.
Tapt instructions are still coming.
This post was edited on 1/29/16 at 9:12 am
Popular
Back to top
![logo](https://images.tigerdroppings.com/images/layout/TDIcon.jpg)