- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
re: My new Glock 19 jams a bunch
Posted on 1/13/14 at 6:52 pm to RATeamWannabe
Posted on 1/13/14 at 6:52 pm to RATeamWannabe
Two factory mags and one aftermarket. Not sure of the name brand.
0
Posted on 1/13/14 at 6:59 pm to dawg23
So im guessing this is the incorrect position for the recoil spring?
Posted on 1/13/14 at 7:04 pm to meauxjeaux2
One other thing. The clip release makes contact with the groove that has no metal on the clip. Is this right?
You can see the metal part on the clip is on the same side as the clip release button. The actual clip release is on the opposite side of the button.
You can see the metal part on the clip is on the same side as the clip release button. The actual clip release is on the opposite side of the button.
Posted on 1/13/14 at 7:19 pm to meauxjeaux2
There is grease all over the inside of that recoil assembly spring. You should take that apart and clean that off. It's a PITA to disassembly but, you probably had better clean that off.
Also, for safety purposes, please unload those magazines (not clips).
Also, for safety purposes, please unload those magazines (not clips).
This post was edited on 1/13/14 at 7:23 pm
Posted on 1/13/14 at 7:26 pm to LSUwag
There is no oil or grease on the recoil pin. Guess the flashmakes it aappear that way. Also, only way im putting a loaded mag in is with the slide off or when im ready to shoot.
Posted on 1/13/14 at 7:33 pm to meauxjeaux2
Which numbers are listed on the ejector?
This post was edited on 1/13/14 at 7:34 pm
Posted on 1/13/14 at 7:37 pm to BAMAisDIESEL09
336
Posted on 1/13/14 at 7:39 pm to meauxjeaux2
quote:
There is no oil or grease on the recoil pin. Guess the flashmakes it aappear that way. Also, only way im putting a loaded mag in is with the slide off or when im ready to shoot.
Okay. I'm a Glock certified armorer and I see nothing wrong in your photos. I would only use the Glock Magazines. My best guess is either too much oil or not enough oil I can't imagine a Glock coming from the factory with issues. Their quality control is very good.
Give it a good cleaning and oil (just a few drops for the 7 contact points that involve the slide and barrel) and try different ammo in your Glock mags, only.
One thing is certain is that Glocks do not operate well with too much oil on them. I recently attended a shooting school where I shot the same Glock 23 for two weeks and it was not cleaned one time. I shot thousands of rounds in very difficult conditions and not one failure to feed. It was filthy dirty when they finally had us break them down to clean them.
Posted on 1/13/14 at 7:40 pm to meauxjeaux2
Bingo. Read my post on page 4 of this thread and google late glock 19 gen 3 ejector issues. People have had problems with the 336 ejector. Try swapping it with the newer ejector and you should see improvement. You need the 30274 ejector.
This post was edited on 1/13/14 at 7:41 pm
Posted on 1/13/14 at 7:46 pm to BAMAisDIESEL09
quote:
late glock 19 gen 3 ejector issues.
Go figure.
Posted on 1/13/14 at 7:46 pm to BAMAisDIESEL09
I was reading people sending their 19s back and Glock replacing both the extractor and ejector. People were complaining about brass to the face. I'm not having that issue.
Posted on 1/13/14 at 7:50 pm to meauxjeaux2
People have had issues with brass to face and jamming. Id suggest buying this:
LINK
Hope this helps.
LINK
Hope this helps.
Posted on 1/13/14 at 7:53 pm to BAMAisDIESEL09
Will order when it becomes available. Thanks for the help. 
Posted on 1/14/14 at 7:40 am to meauxjeaux2
Nope. That's correct.
Posted on 1/14/14 at 11:49 am to meauxjeaux2
quote:
I can meet you there Friday.
Email sent.
Posted on 1/14/14 at 12:05 pm to dawg23
Lol,you gonna die when I call you.We know each other.
Posted on 1/14/14 at 6:24 pm to BAMAisDIESEL09
New ejector ordered. $10 part. Will post results later. Thank you to all who've helped. And to Dawg who has gone fair above helping. Even contacted a FBI gun buddyof his to get me straight.That's what I love about this site.
Posted on 1/14/14 at 6:34 pm to meauxjeaux2
Keep us posted. Hope it fixes the problem.
Posted on 1/14/14 at 6:36 pm to meauxjeaux2
Anticipating recoil possibly?
Posted on 1/14/14 at 6:37 pm to meauxjeaux2
Upgrade to a slotted slide. See if EBC makes one... 
Page 6 of 7
Popular
Back to top
Follow TigerDroppings for LSU Football News