- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Opinions on vinyl wrapping a small fiberglass boat
Posted on 6/13/17 at 8:02 pm
Posted on 6/13/17 at 8:02 pm
Thinking about ordering a carbon fiber vinyl wrap (vivid brand) off of amazon to cover a small (13ft) fiberglass skiff.
The original paint has been sanded away, but it has not been primed yet. Not sure if I should prime it or not, but I believe it would make the vinyl surface smoother.
I'll be watching plenty of youtube videos before installing, but any info on quality brands/application would be appreciated
The original paint has been sanded away, but it has not been primed yet. Not sure if I should prime it or not, but I believe it would make the vinyl surface smoother.
I'll be watching plenty of youtube videos before installing, but any info on quality brands/application would be appreciated
Posted on 6/13/17 at 9:53 pm to MrCoachKlein
vinyl wrap is easy to peel off such as something going into, or if it is constantly being hit with water spray, the water will peel it.
gasoline will destroy and peel vinyl wrap, as in gas spills leaks.
vinyl wrap can only go on over smooth clean dust free sealed surfaces so it needs to be finished, primed, and painted, before you wrap it.
just keep these things in mind and good luck with your project
gasoline will destroy and peel vinyl wrap, as in gas spills leaks.
vinyl wrap can only go on over smooth clean dust free sealed surfaces so it needs to be finished, primed, and painted, before you wrap it.
just keep these things in mind and good luck with your project
This post was edited on 6/13/17 at 9:57 pm
Posted on 6/13/17 at 10:28 pm to keakar
Lots of boats are being wrapped these days, pretty sure a 3M marine grade wrap would hold up on the sides of the hull. The bottom will coated with gator glide
Posted on 6/14/17 at 6:41 am to MrCoachKlein
I would only do it if you can put HUK on each side
Posted on 6/14/17 at 7:56 am to keakar
quote:
vinyl wrap is easy to peel off such as something going into, or if it is constantly being hit with water spray, the water will peel it.
Not true. If you use the proper vinyl and apply it correctly it will hold up just fine. I know of an offshore boat that has had a wrap on for 7 years now and the water hasn't "peeled it".
quote:
gasoline will destroy and peel vinyl wrap, as in gas spills leaks.
Gas will only destroy cheap calendared vinyl. High quality cast vinyl with an overlaminate, or a vinyl like 3M 1080 series will be just fine if gas spills on it.
quote:
vinyl wrap can only go on over smooth clean dust free sealed surfaces so it needs to be finished, primed, and painted, before you wrap it.
Smooth primed surface is fine for a wrap. It doesn't have to be painted as long as it is sealed with primer and smooth. For a glass boat just make sure the surface is smooth and there isn't any wax on it.
To the OP, if you are using the textured carbon fiber style wrap keep in mind it holds dirt and mud so it's hard to clean compared to a regular vinyl. Also, I would go with a more reputable brand than vivid (3M, Arlon, Avery). I wouldn't go below the water line, but if you have to then make sure you use an edge sealing tape or glue. Take your time and be patient. Use a heat gun or torch to help with the application. The hardest part is going to be where the boat starts to turn to the point on the bow.
Posted on 6/14/17 at 8:07 am to jdavid1
high grade vinyl regardless of brand will hold up...
IF you start with a pristine surface.....
bad surface... no dice....
IF you start with a pristine surface.....
bad surface... no dice....
Posted on 6/14/17 at 9:47 am to 34venture
Sushi, word on the skreet is that you're the vinyl king. What would installation run a small boat like mine?
This post was edited on 6/14/17 at 9:50 am
Posted on 6/14/17 at 10:00 am to MrCoachKlein
For top vinyl 6 per sq foot...
labor 5 per sq foot...
labor 5 per sq foot...
Posted on 6/14/17 at 10:20 am to choupiquesushi
quote:
For top vinyl 6 per sq foot...
labor 5 per sq foot...
and 6 months per sf for you to do, correct?
Popular
Back to top
Follow TigerDroppings for LSU Football News