- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Any mechanics on here?
Posted on 2/17/24 at 5:50 am
Posted on 2/17/24 at 5:50 am
I changed out an old serpentine belt with a new one from o’reilly’s. It’s a Gates belt.
My issue is now I get a sporadic but pronounced squeal/chirp for about a half second to a second on cold starts right as engine fires up. Doesn’t occur as it’s turning over and goes away completely after. No noises or loss to performance.
Been reading a lot of forums and can’t find anyone with the same problem. Most are failing pulleys or tensioners but there’s a constant noise for that diagnosis.
TIA
My issue is now I get a sporadic but pronounced squeal/chirp for about a half second to a second on cold starts right as engine fires up. Doesn’t occur as it’s turning over and goes away completely after. No noises or loss to performance.
Been reading a lot of forums and can’t find anyone with the same problem. Most are failing pulleys or tensioners but there’s a constant noise for that diagnosis.
TIA
Posted on 2/17/24 at 6:03 am to TaderSalad
Probably new belt issue. Should go away.
Posted on 2/17/24 at 6:50 am to TaderSalad
put some belt dressing on it and see if that helps until it gets broken in.
Posted on 2/17/24 at 9:16 am to TaderSalad
You probably need a new belt tensioner too. Spring can get weak , also tensioner can lean out and not be in alignment with all other pulling. Also we we used to wire brush the paint off the new tensioner cause it can transfer onto Belt and cause noise too. I worked at a Chrysler dealer. Changed many belts and tensioners. We would not ever change just the belt. Hope this helps.
Posted on 2/17/24 at 12:11 pm to TaderSalad
My first thought is did you get the correct replacement belt from gates?
Second, how many miles do you have on the vehicle? I usually replace belt tensioner when I replace the belts at 60,000 miles. Belt dressing helps.
Good luck.
Second, how many miles do you have on the vehicle? I usually replace belt tensioner when I replace the belts at 60,000 miles. Belt dressing helps.
Good luck.
Posted on 2/17/24 at 5:23 pm to TaderSalad
Double check your belt routing. One of the mechanics I work with had a similar chirp on his Tundra and I went and looked at it and the belt was routed wrong. Once he got that straightened out the noise went away. It's not hard to do and I'm talking about an aircraft mechanic with years of experience.
Posted on 2/17/24 at 9:08 pm to TaderSalad
I had a belt (low hours) making noises on my C3 Vette. It’s got a serpentine on an LS1.
I got tired of spraying the belt dressing, installed a new OEM belt and the noise disappeared.
I got tired of spraying the belt dressing, installed a new OEM belt and the noise disappeared.
Posted on 2/18/24 at 9:36 am to TaderSalad
Rub a bar off of soap on the inside of belt carefully while motor is running. Seriously. It works. Better than any belt dressing. Just hold it against it for 5 seconds or so.
Popular
Back to top
Follow TigerDroppings for LSU Football News