- My Forums
- Tiger Rant
- LSU Recruiting
- SEC Rant
- Saints Talk
- Pelicans Talk
- More Sports Board
- Fantasy Sports
- Golf Board
- Soccer Board
- O-T Lounge
- Tech Board
- Home/Garden Board
- Outdoor Board
- Health/Fitness Board
- Movie/TV Board
- Book Board
- Music Board
- Political Talk
- Money Talk
- Fark Board
- Gaming Board
- Travel Board
- Food/Drink Board
- Ticket Exchange
- TD Help Board
Customize My Forums- View All Forums
- Show Left Links
- Topic Sort Options
- Trending Topics
- Recent Topics
- Active Topics
Started By
Message
Home network setup help (running cat 5)
Posted on 2/9/17 at 10:28 am
Posted on 2/9/17 at 10:28 am
Right now I have a Cat 5 wire from my router plugged in upstairs and have traced the correct wire down to the panel in my basement. If I connect it, should every connection on the panel now receive an internet signal? I would prefer for all Cat 5 connections in the house to be active, but at minimum I want to be able to connect my basement office Cat 5 connection to the router upstairs.
I am a rookie at this. Just tryin this based off You tube vids
4th connection down is the wire from the router. I used "A" connection pattern for all Cat 5 wall plates. Any advice would be appreciated
I am a rookie at this. Just tryin this based off You tube vids
4th connection down is the wire from the router. I used "A" connection pattern for all Cat 5 wall plates. Any advice would be appreciated
Posted on 2/9/17 at 11:30 am to DawgCountry
well apparently this is a bridged telephone distribution board and cannot be used to distribute Ethernet.
would something like this work?
LINK
would something like this work?
LINK
Posted on 2/9/17 at 11:42 am to DawgCountry
The frick are you trying to do?
Terminate them as RJ45 and get a switch.
If you insist on punching them down do a little reading about how to do it properly. I.E. Keep the integrity of the twists as close to the connection as possible and don't expose more than 1/2" of bare wires.
Terminate them as RJ45 and get a switch.
If you insist on punching them down do a little reading about how to do it properly. I.E. Keep the integrity of the twists as close to the connection as possible and don't expose more than 1/2" of bare wires.
This post was edited on 2/9/17 at 11:44 am
Posted on 2/9/17 at 12:04 pm to DawgCountry
A patch panel would work, but then you'd need patch cables to run from the panel to a switch. Would be cheaper to just cap them with RJ45 like mentioned above.
Just make sure you terminate the cable using the A pattern if that's what you used at the wall plate. Most people use the B pattern.
Just make sure you terminate the cable using the A pattern if that's what you used at the wall plate. Most people use the B pattern.
Posted on 2/9/17 at 12:10 pm to DawgCountry
For the OP. "A" standard means order in the RJ45 jack is green white/green/orange white/blue/blue white/orange/brown white/brown.
"B" standard reverses the greens and oranges. Orange white/orange/green white/blue/blue white/green/brown white/brown.
"B" standard reverses the greens and oranges. Orange white/orange/green white/blue/blue white/green/brown white/brown.
Posted on 2/9/17 at 12:25 pm to VABuckeye
I told you I didn't know what I was doing
But most of the wire mess was already like this from the previous owner. I just finally decided today I would see if I can get all of this straightened up since the Cat 5 is ran throughout the house
I assume the switch has an input and multiple outputs?
But most of the wire mess was already like this from the previous owner. I just finally decided today I would see if I can get all of this straightened up since the Cat 5 is ran throughout the house
I assume the switch has an input and multiple outputs?
Posted on 2/9/17 at 12:39 pm to DawgCountry
I figured it wasn't your work. A switch looks like this. You just need a dumb switch. Hook your input up to any port and your outputs up to any ports and you'll have connection. Switches come in a wide variety or port numbers depending on your needs. It looks like an 8 port switch would do for you although a 16 would allow for future expansion.
Posted on 2/9/17 at 1:28 pm to DawgCountry
This is awesome
This post was edited on 2/14/17 at 7:09 pm
Posted on 2/9/17 at 3:34 pm to TrebleHook
I was thinking the same thing... damn, why is he tearing his shite up
Hey OP, put your shite back together and listen to advice below
Posted on 2/9/17 at 8:59 pm to DawgCountry
You sure the Cat 5 wasn't run for use as phone cable?
Posted on 2/10/17 at 12:45 pm to Jimbeaux28
Doesn't matter if it was. Ethernet only needs 2 pairs, POTS or VoIP only need 1 leaving him with an extra. From the looks of it he has homeruns to several rooms.
If the switch is placed there he can then use patch cables and terminate the white/orange and white/green pairs down on keystones to send the signal via Ethernet to whatever rooms have the wiring.
Just make sure at those jacks that you punch the wires down exactly the same way as you did at the patch panel. If you are feeding POSTS or VoIP to those jacks just make sure there is a separate keystone and that the wire is punched down on white/blue in the keystone.
If the switch is placed there he can then use patch cables and terminate the white/orange and white/green pairs down on keystones to send the signal via Ethernet to whatever rooms have the wiring.
Just make sure at those jacks that you punch the wires down exactly the same way as you did at the patch panel. If you are feeding POSTS or VoIP to those jacks just make sure there is a separate keystone and that the wire is punched down on white/blue in the keystone.
Posted on 2/10/17 at 1:48 pm to BottleGnome
quote:
Ethernet only needs 2 pairs
I wouldn't recommend running POTS and Ethernet in the same cable unless it is absolutely necessary.
Posted on 2/10/17 at 9:53 pm to VABuckeye
Running in this configuration will not cause issues unless the cable is bad. When we install internet for customers who keep their POTS many times the pots will be wired in all the way to the jack where the gateway is and then split there to be sent back out to the nid to connect to the inside wire. I have not run into any issues doing this and it is the company preferred way to do it.
Posted on 2/10/17 at 10:31 pm to BottleGnome
Welcome to 2005. You are limiting the customers bandwidth.
Posted on 2/11/17 at 5:52 pm to BottleGnome
quote:
it is the company preferred way to do it.
Less attic time and save money huh? Gotcha. Run a designated data cable for your customers and quit being a cheap lazy arse.
Posted on 2/11/17 at 6:21 pm to RealityTiger
It has nothing to do with being lazy. When I'm told to do my job a certain way that's how it gets done. If you are concerned about voltage it's not really an issue. The wire is twisted for a reason. With all of the POTS customers we have that have lines shared with ADSL or VDSL signals we would notice if there was a problem sharing the lines.
Look at it this way. Your cable pair is in the same main cable with many other customers. Some obviously have POTS on them. The cable in the ground and in the air has less twists than the service drop from the terminal or pedestal to your house. It has even less twists than the cat5 hr from the nid to the gateway. So again if it really was a problem it wouldn't be done.
I'm not one of those people who avoid attics. I actually prefer to go in them since it keeps the wiring out of sight. Do not confuse me with some corner-cutting contractor. My supplies are all paid for by the company so I really don't care how much material it takes to get the job done. I don't see the cost so it's irrelevant to me.
Look at it this way. Your cable pair is in the same main cable with many other customers. Some obviously have POTS on them. The cable in the ground and in the air has less twists than the service drop from the terminal or pedestal to your house. It has even less twists than the cat5 hr from the nid to the gateway. So again if it really was a problem it wouldn't be done.
I'm not one of those people who avoid attics. I actually prefer to go in them since it keeps the wiring out of sight. Do not confuse me with some corner-cutting contractor. My supplies are all paid for by the company so I really don't care how much material it takes to get the job done. I don't see the cost so it's irrelevant to me.
Posted on 2/12/17 at 7:56 am to Jimbeaux28
quote:
You sure the Cat 5 wasn't run for use as phone cable?
Probably. Previous owner was a GT grad. Figured he knew his shite but obviously not. He tore that shite up
Posted on 2/14/17 at 4:27 pm to DawgCountry
OBTW that looks like shite....Just saying. Google is your friend.
Popular
Back to top
Follow TigerDroppings for LSU Football News